Cove Dishwashers Installation Guide

text-h3

Warning: States a hazard that may cause serious injury or death if precautions are not followed.

Caution: Signals a situation where minor injury or product damage may occur if you do not follow instructions.

Introduction

ugxVmyx4VgA

[Music] before you begin the installation of a cove dishwasher view this entire video to familiarize yourself with the process use a qualified installer for installation of a cove dishwasher [Music] to safely and efficiently install cove dishwashers watch for the following types of highlighted information caution signals the need to follow instructions to avoid minor injury or product damage warning indicates the need to follow instructions to avoid a hazard that may cause serious

2020-09-16T00:00:00.000Z

PT0M37S

false

Site Preparation

GHmX3eD7GPs

[Music] measure and verify that the opening dimensions are consistent with the installation guide shipped with the product [Music] remember before moving the dishwasher protect the finished flooring note finish three and a half inch returns as they are visible and should match the cabinetry

2020-09-16T00:00:00.000Z

PT0M23S

false

Electrical Requirements

xEZ83bHDgSg

installation must comply with all applicable electrical codes the longest dimension of any opening into the adjacent cabinet must not be more than one and a half inches locate the electrical supply in an adjacent cabinet within reach of the power cord the appliance requires a separate circuit serving only this appliance the installation may require a ground fault circuit interrupter gfci outlet or a breaker whichever complies with local codes improper connection of the equipment grounding conductor can result in a risk of electric shock check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician

2020-09-16T00:00:00.000Z

PT1M0S

false

Plumbing Requirements

yDJkiIpE0aM

2020-09-16T00:00:00.000Z

PT0M54S

false

Door Panels

OCe99CUbmdo

[Music] stainless steel accessory door panels are available through an authorized cove dealer for local dealer information visit the find a showroom section of our website at coveappliance.com the thickness of the custom panel can vary the product requires a minimum one-half inch thick panel but the thickness can increase provided the panel does not exceed 20 pounds the custom door panel template provided accommodates 23 and 3 8 inch and 23 and three quarters inch wide panels adjust the template accordingly for all finish all sides of the custom panel they may be visible when the door is open

2020-09-16T00:00:00.000Z

PT0M50S

false

Custom Panel Mounting

qbwXdNZhX_c

[Music] use caution when drilling bracket holes to prevent damage number one remove the template from the dishwasher door number two place the custom panel face down on a protected work surface number 3 position the template flush with the top and sides of the panel [Music] number four remove the custom panel mounting brackets from the dishwasher number five use the screws provided to secure brackets to the panel [Music] number six align the mounting pins on the door panel with the dishwasher door slots then push in and shift the panel down to secure number seven verify the panel is secure against the dishwasher door then insert a screw into each hinge to number eight finger tighten the adjustment bracket nuts [Music] number nine place the kick plate magnetic strike plates on the magnets and remove the adhesive backing [Music] number 10 push the kick plate panel number 12 remove the kick plate then wrench tighten the bracket nuts [Music]

2020-09-16T00:00:00.000Z

PT2M2S

false

Preparation

7TfGQi-fF5k

number one ensure the unit is in front of the opening number two for openings less than 24 inches wide remove the side spacers by pushing upward number three measure the height of the opening then adjust the leveling legs until the unit height is slightly smaller number four to adjust the front turn the leveling legs clockwise to raise to adjust the rear turn the rear adjustment screw counterclockwise to raise and clockwise to lower the unit the unit design prevents the rear leveling leg from stripping if turned the wrong way if the rear leveling leg does not raise or lower tilt the dishwasher forward slightly to remove pressure from the leg this engages the threads number five route the power cord through an access hole in the adjacent cabinet number six route the water supply and drain tube through an access hole in the number seven remove the racks before anchoring the unit to remove the upper and middle racks number one pull the rack out to full extension number two pull out on the tab on the side of the rack clips and remove the clips from the end of each rack glide number three pull the rack forward to remove to remove the lower rack number one pull the rack out to full extension

2020-09-16T00:00:00.000Z

PT2M14S

false

Installation

ExzrjdnSlxI

number one insert the unit into the opening and pull the excess electrical and plumbing supplies through the access hole before completing the installation number two verify that plumbing and electrical supplies are not kinked or coiled number one connect the drain line by following the local code the drain connection will accommodate one inch three quarters inch and five eighths inch drain connections cut the connection to fit three quarter inch and 5 8 inch connections if connecting to a food waste disposal remove the knockout before making the drain connection secure the drain tube between 20 inches and 43 inches above the bottom of the dishwasher number two connect the water connection to the water supply with the fitting provided make sure to remove the knockout from the waste disposal before making the drain connection failure to do so will cause drain issues number one route the product end of the power cord through the one and a half inch cabinet access hole when routing the power cord through metal protect the edges of the access hole to prevent abrasion number two plug the cord into the back of the unit and then

2020-09-16T00:00:00.000Z

PT1M34S

false

Leveling

18HBjsXmuPg

[Music] to adjust the front turn the leveling legs clockwise to raise and counterclockwise to lower the unit to adjust the rear turn the rear adjustment screw counterclockwise to raise and clockwise

2020-09-16T00:00:00.000Z

PT0M19S

false

Anchoring

-7XgbhTr-rA

[Music] secure the unit to adjacent cabinetry using the screws provided do not over tighten over tightening could distort the unit causing issues with the door seal if applicable secure the top of the unit to the countertop using the screws provided verify proper door closure then install the hole plugs in each

2020-09-16T00:00:00.000Z

PT0M28S

false

Door Tension Adjustment

d2fvkmZlapE

door tension adjustment accommodates multiple panel weights panel weight cannot exceed 20 pounds turn the adjustment nut clockwise to increase tension

2020-09-16T00:00:00.000Z

PT0M17S

false

Kickplate Installation

5w-Y9pvAxDE

the kick plate must be removable for service the floor cannot interfere with removal to remove the kick plate number one finger tighten the adjustment bracket nuts number two place the kick plate on the magnets number three make in and out adjustments number four remove the kick plate then wrench tighten the bracket nuts [Applause] a decorative kick plate may be adhered to the existing kick plate the height and thickness can vary but the addition must not impede the door panel rotation notch the upper right corner of any kick plate exceeding 3 and 3 8 inch in height to allow for air flow

2020-09-16T00:00:00.000Z

PT0M59S

false

Completion

CTGRjoBcZqc

2020-09-16T00:00:00.000Z

PT2M12S

false

palette

stone--dark

/content/subzero-wolf-eds/us/en/fragments/pre-footer

palette

grey--off-white